Though it may seem like a pain, it’s worth it to take the extra couple minutes to make sure you don’t accidentally drop your pallet due to a faulty pallet jack. You will want to look for things such as loose prongs, unbalanced wheels, or charging cords that aren’t stowed properly. One of the most important steps before operating a pallet jack is to take a look and make sure everything appears ready and functional. Though they are relatively simple machines, pallet jacks can still be dangerous if the proper safety precautions aren’t taken. However, humans are able to push much more weight than they can pull and excessive pulling can result in injury. You can push and pull a pallet jack, depending on how you need to maneuver it. You will need to pull out the charging cord from its storage area in the machine, and plug it back in so that the electric pallet jack will be ready for use the next time it is needed. When you’re finished, put the electric pallet jack back as you found it. When you arrive, again press the “down” button to lower the prongs and pallet to the floor. Once you have your pallet securely loaded, you can use the control buttons to move to your destination. Then, press the “up” button to lift the pallet and prongs off the ground. Once you arrive in front of your pallet, use the buttons to maneuver the prongs underneath and all the way through the pallet. Next, use the controls to move the pallet jack to your destination. Again, these should be about one to two inches from the ground. Push the “down” button to lower the prongs toward the floor. On the handle of the pallet jack, there should be buttons to control the direction of movement. There is usually an obvious location to insert and store the length of the cord. Because they run on electricity, electric power jacks need to be plugged in and charged when they are not in use. Your first step for operating an electric pallet jack is to unplug the charging cord and store it away inside the machine. Unplug the electric pallet jack’s plug when you are using it. Many also have a “ride-on” feature that can make it easier to get around a large warehouse. How to Operate an Electric Pallet JackĮlectric pallet jacks can be even more convenient to use than manual pallet jacks, as the manual motion of jacking up the prongs is done electronically. Repeat this several times so that the prongs are far enough off the floor not to drag. You should feel some resistance and notice the prongs slowly lift up the pallet. Once the prongs are positioned underneath the pallet, pull the metal handle and the entire center bar toward you at an angle. Jack Up the PalletĪnimation showing the pallet being lifted due to pushing down the handle. Make sure you push the prongs all the way through the underside of the pallet so the wheels are resting on the floor and not on any part of the pallet. If they are still too high to easily slide under the pallet, they may not be lowered all the way and you should press the release lever again. Once the prongs have been completely lowered, you can slide them underneath the pallet you want to move. Slide the Prongs Under the Pallet to Load If the prongs are already lowered, they will not move when you press the lever. Press the release lever up and inward to lower the prongs to about one-inch off of the ground. Next, push the pallet jack over to the pallet you would like to move. Move the pallet jack to whatever you want to move and engage the lever to lower the prongs. It may be a different color in order to make it stand out, but if not it should still be obvious. Locate the plastic release lever on the handle this is usually found attached to the center bar. The prongs are the two horizontal pieces of metal that actually lift the pallets. Stand behind the pallet jack with your hands on the metal steering handle, toward the outward-facing prongs. Here are the four simple steps for using a manual pallet jack. They can be a good choice for small to mid-sized warehouses or construction sites. Manual pallet jacks are simpler and more affordable than electric pallet jacks, and also require less upkeep. If you’re thinking about investing in one of these tools but are wondering how to use a pallet jack, take a look at the step-by-step instructions below. Both can be good options depending on the size and scope of the project. These tools come in two variations: manual pallet jacks and electric pallet jacks. Cheaper and easier to operate than forklifts, and safer than manual labor, pallet jacks are used for transporting small loads for short distances. Pallet jacks are some of the most essential tools found in warehouses and construction sites.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |